1. Enter setting mode: Press the Panic Button A, followed by entering the current PIN (factory default code is 0000)
   (The LED will now flash continuously.)
2. Press Panic Button B.
3. Enter new 4-digit PIN.
4. Press Arm button to confirm.
5. Exit setting mode: Press Disarm twice to quit the changing code process, or wait for 5 minutes for the Key Pad to quit test mode automatically.
   (The LED will now stop flashing.)
   

Step 1

Enter setting mode: Press the Panic Button A, followed by entering the current PIN code (factory default code is 0000).

Step 2

4. Press Arm button to confirm.

Step 3

The LED will now flash continuously.) 2. Press Panic Button B. 3. Enter new 4-digit PIN code.

Step 4

5. Exit setting mode: Press Disarm twice to quit the changing code process, or wait for 5 minutes for the Key Pad to quit test mode automatically. (The LED will now stop flashing.)

Key Pad/Key Fob: Press arm
Control Panel: Press arm

Step 1

On the Key Pad: Press Arm

Step 2

On the Key Fob: Press Arm

Step 3

On the Control Panel: Press Arm

Key Pad: Press Disarm followed by your PIN.
Key Fob: Press Disarm.
(The siren will beep twice and flash.)
Control panel: Light panel up, green disarm key, enter code, tick.

Step 1

On the Key Pad: Press Disarm followed by your PIN code.

Step 2

On the Key Fob: Press Disarm. (The siren will beep twice and flash.)

Step 3

On the Control panel, Light panel up, green disarm key, enter pin code, tick

The PIRs will respond to movement of up to 12 metres away and 110 degrees when placed in the corner of a room, movement is detected from floor to ceiling.

Please see images below for information and instructions:

Step 1

To add a device press button A and then the pin code.

Step 2

Then button A again.

Step 3

Followed by the number 4.

Step 4

Press the button the device you want to add (you’ll get a beep from the siren acknowledging that the device has been learnt in).

Step 5

Then you press button A.

Step 6

Followed by the number 5 – which takes you out of learning mode.

Step 7

Finally you press disarm twice.

Disable the siren tamper via the Key Pad, as per diagram below.

Step 1

Press button A on the keypad and insert your pincode.

Step 2

Then press button A again, followed by the number 2 – that disables the siren tamper.

Step 3

Then you have 1 hour to change the batteries. You cannot arm or disarm it during this hour unless you turn the tamper back on. To do so you press button A then the pincode.

Step 4

Then button A followed by number 3.

Step 5

Then press disarm twice.

Please ensure the battery is inserted in the correct manner, see the picture below.

Step 1

Go into your programme menu (blue menu button, then enter your pin code followed by the tick key), to prevent an alarm activation. Then continue to change the batteries.

Please ensure that the tamper is disabled before you open the Key Pad, as per your manual. Then follow the instructions below:

1. Open the cover and remove the battery.
2. Re-insert with the number “3” key pressed (taking care 3 is held down).
   
3. The Key Pad will go back to the “0000” Key Pad PIN.

Step 1

Ensure that the tamper is disabled before you open the Key Pad, as per your manual.

Step 2

Open cover and remove battery

Step 3

Re-insert with the number “3” key pressed (taking care 3 is held down). The Key Pad will go back to the “0000” Key Pad code.

See image below for more information:

The PIRs will respond to movement of up to 12 metres away and 110 degrees when placed in the corner of a room, movement is detected from floor to ceiling.

Your keypad may not be programmed in correctly to the siren.

1. You must take down the siren to do this (you may find the alarm will go off)
2. Turn the siren off using the on/off switch inside the siren, leave it off for 1 minute, then turn it back on and it will beep and flash. If this does not work, please remove one battery from the siren and leave it for at least 5 minutes and then place it back in
3. Once this has happened please press the buttons on every device (please note the siren should beep every time a button is pressed on a device) to learn them back into the siren
4. To learn the keypad back in press buttons 8 & 9 at the same time

Step 1

You must take down the siren to do this (you may find the alarm will go off). Turn the siren off using the on/off switch inside the siren, leave it off for 1 minute, then turn it back on and it will beep and flash. If this does not work, please remove one battery from the siren and leave it for at least 5 minutes and then place it back in.

Step 2

Once this has happened please press the buttons on every device (please note the siren should beep every time a button is pressed on a device) to learn them back into the siren. To learn the keypad back in press buttons 8 & 9 at the same time.

This is because the batteries are low. Please see instructions on how to change the batteries. 

Step 1

Press button A on the keypad and insert your pin code

Step 2

Then press button A again, followed by the number 2 - This disables the siren tamper

Step 3

You have 1 hour to change the batteries. You cannot arm or disarm it during this hour unless you turn the tamper back on.

Step 4

To turn the arm or disarm back on, press the button A then enter your pin code

Step 5

Press button A followed by number 3

Step 6

Then disarm twice

The siren tamper may not be fully depressed. Please check that the siren tamper switch/spring is depressed to its fullest. Some packing may be required if the siren is mounted on an uneven surface.

Please check that the siren tamper switch/spring Is depressed to its fullest. Some packing may be required if the siren is mounted on an uneven surface.

The PIR goes into sleep mode for two minutes. Please vacate the area covered by the PIR for a full 2 minutes before testing.